Door & Cabinet Hardware Installation Instructions
Push Plate, Door Handle, Fleur De Lis Door Knocker, Decorative Straps, Wrought Iron Rings
To install Door Hardware, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
1"-#8 Screws provided with caps. If you are not mounting your hardware into a stud, anchors will be needed.
Measure and Mark: Determine the placement of the door hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the door.
Attach Hardware: Line up door hardware with pilot holes. Hardware includes a screw, black washer, silver washer, and plastic cap to give the look of a rivet. First, drop the silver washer on the screw to cup up over the screwhead. Second, twist on the black washer in that same orientation (will sit between the mounting service and cap). Drill the screw into the mounting surface and tighten the screws with a screwdriver, being careful not to over-tighten. Finish by snapping the plastic cap onto the silver washer.
Wrought Iron Door Knocker with Long Back Plate
To install Long Back Plate Door Knocker, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
1”- #8 Screws provided.
Measure and Mark: Determine the placement of the door hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the door.
Attach Hardware: Line up door hardware with pilot holes and tighten the screws with a screwdriver, being careful not to over-tighten.
Cabinet Knobs, Ring Pulls, Drawer Pulls
To install cabinet Pulls, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level. 1.25”- 10-32 screw provided.
Measure and Mark: Determine the placement of the cabinet hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Insert the fastening screws through the back of the holes.
Attach Pulls: Thread the screw into the iron hardware and tighten them with a screwdriver, being careful not to over-tighten.
Wrought Iron Drawer Pull with Decorative ends
To install Handle, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
1"-#8 Screws provided with optional caps.
Measure and Mark: Determine the placement of the door hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the door.
Attach Hardware: Line up door hardware with pilot holes. Hardware includes a screw, black washer, silver washer, and plastic cap to give the look of a rivet. First, drop the silver washer on the screw to cup up over the screwhead. Second, twist on the black washer in that same orientation (will sit between the mounting service and cap). Drill the screw into the mounting surface and tighten the screws with a screwdriver, being careful not to over-tighten. Finish by snapping the plastic cap onto the silver washer.
Wrought Iron Door Handle 1.5in x 16in, Hammered Cabinet Iron Pull 16”
To install Door handle, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level. 2”- ¼-20 Hex head bolt provided.
Measure and Mark: Determine the placement of the handle by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Insert the fastening screws through the back of the holes.
Attach Hardware: Thread the bolt into the iron handle and tighten them with a wrench, being careful not to over-tighten.
Shelf and Mantle Brackets
To install Iron Shelf brackets, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
2"-#8 Screws or 1 ½” #12 screws provided with caps. If you are not mounting your hardware into a stud, anchors will be needed.
Measure and Mark: Determine the placement of the door hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the door.
Attach Hardware: Line up door hardware with pilot holes. Hardware includes a screw, black washer, silver washer, and plastic cap to give the look of a rivet. First, drop the silver washer on the screw to cup up over the screwhead. Second, twist on the black washer in that same orientation (will sit between the mounting service and cap). Drill the screw into the mounting surface and tighten the screws with a screwdriver, being careful not to over-tighten. Finish by snapping the plastic cap onto the silver washer.
Hinge Straps
To install Iron Hinge Strap, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
Dependent on strap size: 2"-#8 Screws or 1 ½” #12 screws provided with optional caps.
Measure and Mark: Determine the placement of the door hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the door.
Attach Hardware: Line up door hardware with pilot holes. Hardware includes a screw, black washer, silver washer, and plastic cap to give the look of a rivet. First, drop the silver washer on the screw to cup up over the screwhead. Second, twist on the black washer in that same orientation (will sit between the mounting service and cap). Drill the screw into the mounting surface and tighten the screws with a screwdriver, being careful not to over-tighten. Finish by snapping the plastic cap onto the silver washer.
Bath Hardware
To install Bath Hardware, follow these steps:
Gather Tools: You will need a tape measure, pencil, drill, screwdriver, and level.
2"-#8 Screws with caps provided.
Measure and Mark: Determine the placement of the bath hardware by measuring and marking where the holes will go.
Pre-drill Holes: Use a drill to create holes at the marked locations.
Insert Screws: Drill pilot hole into the marked locations on the mounting surface.
Attach Hardware: Line up bath hardware with pilot holes. Hardware includes a screw, black washer, silver washer, and plastic cap to give the look of a rivet. First, drop the silver washer on the screw to cup up over the screwhead. Second, twist on the black washer in that same orientation (will sit between the mounting service and cap). Drill the screw into the mounting surface and tighten the screws with a screwdriver, being careful not to over-tighten. Finish by snapping the plastic cap onto the silver washer.